While you won't want to try floating it, this DIY concrete and driftwood sailboat is a breezy nautical or coastal decor idea for your home or cottage.
Age Group: Adult Crafts
Author: JANE & SONJA
boat-shaped molde.g. a beach toy
straight driftwood pieceabout 12” long
sand for concrete
container with water
container for mixing
spoons for scooping ingredients and for mixing
drill and small drill bit
12”x12” nautical themed scrapbook paper
Making the Concrete Boat
Start to make your DIY concrete and driftwood sailboat by generously coating your boat mold with a release agent such as vegetable oil.
Use a measuring cup to measure equal amounts of sand and cement (two cups of each in this case). Thoroughly blend them together.
The amount of water that you need to add to the mixture will depend on the moisture level of the sand to begin with. Start by adding a half part (e.g. 1 cup) of water to the cement mixture. It’s better to start with less water and then add more if needed. You’re aiming for a thick dough-like consistency.
My mixture felt quite thin, so I added a bit more each of the sand and cement to the mixture.
Either pour or scoop your concrete mixture in your mold. Don’t overfill.
Gently tap the mold on the table top to level the concrete and help move air bubbles to the surface.
Place the filled boat mold on a level surface and let for at least one hour before inserting the driftwood mast.
Note: If the concrete appears to be drying too quickly (e.g. hot weather), consider spraying the surface with water at the beginning to keep it from cracking. Cement cures, not dry. And needs to stay moist to cure properly.
Adding the Sailboat Mast and Eyelets
Once the concrete has firmed up a bit, try inserting the driftwood mast, about 1/3 of the way from the front of the boat. It should be able to stand up on its own. If not, wait another hour and try to insert the driftwood again. Jiggle the boat to help the cement settle around the driftwood.
Insert a small eyelet close to the back of the boat before the concrete sets completely. Let the concrete boat completely cure 24-48 hours.
Remove concrete from the mold.
Gently sand all edges.
Drill two small eyelet holes in the driftwood mast: 1” from the top and 1” from the surface of the concrete boat. Ensure that the holes are facing towards the back of the boat.
Screw eyelets into each of the drilled pilot holes.
Mounting the Sail
Measure the distances between the three eyelets to determine how the sail needs to be cut. Add an extra 1” to the length and width of the triangle.
Use those measures to mark and then cut a triangular shaped sail from the nautical scrapbook paper.
Use the cut sail as a template to cut a second sail. Ensure that the pattern on the print is in the same direction for both pieces of paper. (Note: this step isn’t necessary if you use 2-sided scrapbook paper).
Using a double sided piece of tape, apply tape to back side of one cut triangle. Stick the two wrong sides together and trim away any uneven edges.
Hold the cut triangle up to your sailboat to roughly mark the placement of the holes. Alternatively, you can measure the distance between the eyelets (length and width) and mark them onto the triangle cut paper. Using a hole punch, insert your cut paper and punch one hole over top of your markings.
Begin attaching the sail to the boat by aligning the hole punches on the paper with the eyelets on the boat. Loosely tie them together using a piece of cut twine.
There you go! A beautiful nautical driftwood sailboat that’s perfect for your coastal decorating. We think this piece would be great for the cottage or home, especially in a beach-themed nursery or bedroom. It would also make a great gift idea for any sailboat lover!
This project for DIY Concrete and Driftwood Sailboat was printed from CraftsbyAmanda.com - https://craftsbyamanda.com/diy-concrete-driftwood-sailboat/ and can only be printed for education or personal use.