I love working with deco mesh. You can see evidence of this in my studio with these deco mesh flowers and this deco mesh poinsettia for Christmas. I didn’t have a wreath for fall, so I actually took some inspiration from my deco mesh dandelions to create this deco mesh pumpkin wreath!
You can get deco mesh from just about any craft supply store, big box stores like Walmart will have a limited selection, and you can buy it online as well.
For this pumpkin wreath you will need TWO of the 10-inch x 10-yard rolls. You could probably get away with one, but it’s better to be safe than sorry! And if you don’t use the second one you can always return it.
Deco Mesh Pumpkin Wreath
As I mentioned above, I drew some inspiration for this deco mesh pumpkin wreath from my dandelion flowers that are hanging on my studio wall. You’ll notice that when you watch the video at the end of this post. The video is of me making the yellow dandelion flower, but it’s the same exact method for the pumpkin. See it all the way down above the printable version!
Here’s the supply list for this project. Full disclosure, I used Floracraft decorative mesh, but they don’t have orange on Amazon. So I linked to a similar product on amazon below. You should be able to easily find this at Michaels, Hobby Lobby, and probably even at WalMart.
You will need:
- 2 rolls 10-inch x 10-yard orange decorative mesh
- 6-inch (5 7/8″) Styrofoam disc
- U-shaped floral pins
- 24-inches of 10-inch green decorative mesh OR a sheet of green felt
- 1 sheet orange felt
- 4 large silk leaves with stems (see tip below)
- Raffia
- 12″ long piece orange ribbon
- Hot glue gun
CRAFT TIP: you can buy small bags of silk leaves or you can use leaves that come with silk flowers. If you only have leaves without stems, glue them to popsicle sticks so that you will be able to insert the sticks into the Styrofoam. This is necessary in order for the leaves to be high enough to be seen from behind the deco mesh rolls of the pumpkin.
I highly recommend that you watch the video above as it shows the process for creating the “tube flower” that is the base of the pumpkin. This is a photo of the beginning of that process.
- Cut the roll of deco mesh into 10-inch lengths giving you fairly equal squares of mesh.
- Roll a square and insert a floral pin in the center of the tube.
- Fold at the center and add a dab of hot glue near the floral pin prongs.
- Insert the pin on an angle into the edge of the Styrofoam disc.
- Continue this process around the circle and work your way into the center until the disc is full.
- Turn the orange tube flower upside down so that the Styrofoam disc is face up.
Cut a 24-inch long piece of green deco mesh. Roll this into a loose tube so that the resulting tube is twice as large as the orange tubes.
Insert floral pin at the lower third of the tube.
Apply some hot glue near the prongs and insert into the top end of the disc.
Insert the leaf stems into the top end of the disc on either side of the green tube.
Tie orange ribbon into a loop hanger and glue to the disc. The loop should not be visible behind the stem when viewing the wreath from the front.
Cut orange felt to cover the back of the disc and bottom of the stem and hot glue in place. This will also protect your door from scratches! Tie raffia around the green stem.
Hang your beautiful new deco mesh pumpkin wreath on your door!
If you enjoyed this project, you’ll probably like our fabric pumpkins tutorial and our mason jar lid pumpkins!
- 2 rolls 10-inch x 10-yard orange decorative mesh
- 6-inch (5⅞") Styrofoam disc
- U-shaped floral pins
- 24-inches of 10-inch green decorative mesh OR a sheet of green felt
- 1 sheet orange felt
- 4 large silk leaves with stems (see tip below)
- Raffia
- 12" long piece orange ribbon
- Hot glue gun
- Cut the roll of deco mesh into 10-inch lengths giving you fairly equal squares of mesh.
- Roll a square and insert a floral pin in the center of the tube.
- Fold at the center and add a dab of hot glue near the floral pin prongs.
- Insert the pin on an angle into the edge of the Styrofoam disc.
- Continue this process around the circle and work your way into the center until the disc is full.
- Turn the orange tube flower upside down so that the Styrofoam disc is face up.
- Cut a 24-inch long piece of green deco mesh.
- Roll this into a loose tube so that the resulting tube is twice as large as the orange tubes.
- Insert floral pin at the lower third of the tube.
- Apply some hot glue near the prongs and insert into the top end of the disc.
- Insert the leaf stems into the top end of the disc on either side of the green tube.
- Tie orange ribbon into a loop hanger and glue to the disc. The loop should not be visible behind the stem when viewing the wreath from the front.
- Cut orange felt to cover the back of the disc and bottom of the stem and hot glue in place. This will also protect your door from scratches!
- Tie raffia around the green stem.
Amanda Formaro
Latest posts by Amanda Formaro (see all)
- Tips for Painting on Plastic - August 15, 2018
- 42 DIY Halloween Decorations - August 14, 2018
- Plastic Spoon Bugs on a Branch - August 8, 2018
How do u kept it from it from ravening when u cut it upto make a wire wreath
Hi Pam. Decomesh can definitely fray along the cut lines. I’m not positive that I understand what you are asking though. Are you asking about cutting the mesh for making a regular wreath? Or for making this exact pumpkin wreath project? If your question is regarding this project, when the mesh is rolled up the edges aren’t really exposed so fraying does not seem to be a problem.